1.Product Description
The APF Active Power Filters 3P4W is mainly applied with 4 wire system,it’s IGBT based power converter, detection technology based on instantaneous reactive power theory,automatic tracking of harmonic changes in the grid, Highly controllable and fast responsive. Overcoming the shortcomings of the traditional passive filter, such as poor filtering effect, easy resonance, and only compensation for fixed subharmonics, good filtering and compensation for shock loads of various fast transients,APF Active Power Filters 3P4W can also improve power factor (PF) and correct load imbalances in the power system.
2,Product parameters
Rated Compensation Current |
25-150A in wall mounted 200-750A cabinet parallel configuration |
Altitude Operating Limit |
1% up 2000m(2000-4000m) The power decrease by 1% for every additional 100m |
Rated Voltage(V) |
220V/400V/480V/690V |
Operating temperature |
-10℃ ~ +45℃/ |
Rated Frequency (Hz) |
50HZ/60HZ |
Relative Humidity |
≤95%,Non-condensing |
Functions |
1.Harmonic Compensation 2.Unbalance Correction 3.Power Factor Correction |
Neutral Filtering Capability |
Yes |
Network Configuration |
3P4W |
Noise Level |
<60db |
Parallel Operation |
750A Per Cabinet Or Customized |
CT Ratio |
100;5~6000:5 |
Harmonic Compensation Efficiency |
>97% |
Topology Design |
3 Level |
Harmonic Compensation Capability |
THDi<5% |
Neutral Compensation Capacity |
3 times Rating |
Harmonic Compensation Range |
2nd~50th Order |
Monitoring |
4.3 inch LCD Displayer Or 7 inch Centralized Monitoring |
Full response time |
≤10ms |
Power Loss |
<3% Rated Power |
IGBT Frequency |
20KHz |
Harmonic Spectrum |
2nd~50th Harmonic Order |
Protective function |
16 Ways Protection |
Design Approoval |
EN50065/60146/62477 IEC61000-4-2/5/6/4-12 IEC61000-6-4-2 |
Communication Interface |
RS485,Ehernet |
Certificate |
TUV CE/AS/URL |
Communication Protocol |
MODBU S-RTU protocol |
||
Model |
30A /50A |
75A/100A |
150A |
Wall Mounted Dimensions(mm) |
423W*88D*550H |
503W*190D*597H |
503W*220D*608H |
Rack Mounted Dimensions(mm) |
452.5W*450D*86H |
550.6W*540D*190H |
558W*540D*220H |
Net Weight |
14KGS |
34KGS/37KGS |
44KGS |
Protection Class |
IP 20 |
3.Product feature
※ Low thermal loss (≤3% of rated APF kVA), efficiency ≥ 97%
※ High harmonic filtering rate: Up to 98%
※ High stability: Infinite impedance to grid, avoids harmonic resonance problems
※ Flexible application: Modular design, embedded in standard or customized cabinet
※ High harmonic filtering rate: Up to 98%
※ Modular design Easy installation and maintenance: Plug-in installation for APF module replacement and expansion
※ Wide capacity range: 50A~750A for a single cabinet, or customized
4.Advanced system performance
3 level topology structure
DSP+FPGA high speed operational capability
Automatic resonance avoiding,automatic limiter without overload
Protection:overvoltage,overcurrent,over teaperature.Etc 16 ways protection
Communication:Ethernet,RS485 Etc.
5.Working Principle
External CT detects the load current, DSP tracksinstruction current and calculates the reactive power change rate through the Instantaneous Reactive Power Algorithm. Then DSP sends PWM signal to IGBT driving board which can control IGBT on and off to generate the same amplitude reverse compensation current. At the same time CT detects the output current and compensation result is fed back to DSP, then the next round of logic control is carried out to realize stable power grid.
http://www.coepowers.com/